For feedback, use the following:
ipd_online_feedback@alcatel-lucent.com
Table of Contents Previous Next Index PDF


Common CLI Command Descriptions
In This Chapter
This section provides information about common Command Line Interface (CLI) syntax and command usage.
Topics in this chapter include:
Common Service Commands
sap
Syntax 
[no] sap sap-id
Description 
This command specifies the physical port identifier portion of the SAP definition.
Parameters 
sap-id
The sap-id can be configured in one of the following formats:
 
slot/mda/port[.channel]
[port-id | bundle-id| bpgrp-id | lag-id | aps-id]
port-id: 1/1/3
bundle-id: bundle-ppp-1/1.1
bpgrp-id: bpgrp-ima-1
lag-id: lag-63
aps-id: aps-1
[port-id | bundle-id| bpgrp-id | lag-id | aps-id]:qtag1
port-id:qtag1: 1/1/3:100
bundle-id: bundle-ppp-1/1.1
bpgrp-id: bpgrp-ima-1
lag-id:qtag1:lag-63:102
aps-id:qtag1: aps-1:27
[port-id | bundle-id| bpgrp-id | lag-id]:qtag1.qtag2
port-id:qtag1.qtag2: 1/1/3:100.10
bundle-id: bundle-ppp-1/1.1
bpgrp-id: bpgrp-ima-1
lag-id:qtag1.qtag2:lag-10:
[port-id | aps-id | bundle-id | bpgrp-id][:vpi/vci |vpi |vpi1.vpi2]
bundle-id: bundle-ima-1/1.1
bpgrp-id: bpgrp-ima-1
[port-id | aps-id]:dlci
port-id: 1/1/1:100
aps-id: aps-1
dlci: 16
port-id: 1/1/3.1
Values:
sap-id: null [port-id | bundle-id | bpgrp-id | lag-id | aps-id]
dot1q [port-id | bundle-id | bpgrp-id | lag-id | aps-id]:qtag1
qinq [port-id | bundle-id | bpgrp-id | lag-id]:qtag1.qtag2
atm [port-id | aps-id][:vpi/vci|vpi| vpi1.vpi2]
frame [port-id | aps-id]:dlci
cisco-hdlc slot/mda/port.channel
cem slot/mda/port.channel
ima-grp [bundle-id[:vpi/vci|vpi|vpi1.vpi2]
port-id slot/mda/port[.channel]
bundle-id bundle-type-slot/mda.bundle-num
bundle keyword
type ima, fr, ppp
bundle-num 1 — 256
bpgrp-id bpgrp-type-bpgrp-num
bpgrp keyword
type ima, ppp
bpgrp-num 1 — 1280
aps-id aps-group-id[.channel]
aps keyword
group-id 1 — 64
ccag-id ccag-id.path-id[cc-type]:cc-id
ccag keyword
id 1 — 8
path-id a, b
cc-type .sap-net, .net-sap
cc-id 0 — 4094
eth-tunnel eth-tunnel-tunnel-id
tunnel-id 1 — 1024
eth-tunnel-sap-id 0 — 4094
lag-id lag-id
lag keyword
id 1 — 200
qtag1 0 — 4094
qtag2 *, 0 — 4094
vpi NNI: 0 — 4095
UNI: 0 — 255
vci 1, 2, 5 — 65535
dlci 16 — 1022
ipsec-id ipsec-id.private | public:tag
ipsec keyword
id 1 — 4
tag 0 — 4094
tunnel-id tunnel-id.private|public:tag
tunnel keyword
id 1..16
tag 0..4094
bundle-id
Specifies the multilink bundle to be associated with this IP interface. The bundle keyword must be entered at the beginning of the parameter.
The command syntax must be configured as follows:
bundle-id: bundle-type-slot-id/mda-slot.bundle-num
bundle-id value range: 1 — 256
For example:
*A:ALA-12>config# port bundle-ppp-5/1.1
*A:ALA-12>config>port# multilink-bundle
bgprp-id
Specifies the bundle protection group ID to be associated with this IP interface. The bpgrp keyword must be entered at the beginning of the parameter.
The command syntax must be configured as follows:
bpgrp-id: bpgrp-type-bpgrp-num
type: ima
bpgrp-num value range: 1 — 1280
For example:
*A:ALA-12>config# port bpgrp-ima-1
*A:ALA-12>config>service>vpls$ sap bpgrp-ima-1
qtag1, qtag2
Specifies the encapsulation value used to identify the SAP on the port or sub-port. If this parameter is not specificially defined, the default value is 0.
Values
The values depends on the encapsulation type configured for the interface. The following table describes the allowed values for the port and encapsulation types.
 
The SAP is identified by the 802.1Q tag on the port. Note that a 0 qtag1 value also accepts untagged packets on the dot1q port.
 
sap ipsec-id.private|public:tag
This parameter associates an IPSec group SAP with this interface. This is the public side for an IPSec tunnel. Tunnels referencing this IPSec group in the private side may be created if their local IP is in the subnet of the interface subnet and the routing context specified matches with the one of the interface.
This context will provide a SAP to the tunnel. The operator may associate an ingress and egress QoS policies as well as filters and virtual scheduling contexts. Internally this creates an Ethernet SAP that will be used to send and receive encrypted traffic to and from the MDA. Multiple tunnels can be associated with this SAP. The “tag” will be a dot1q value. The operator may see it as an identifier. The range is limited to 1 — 4095.
 
port
Syntax 
port port-id
Description 
This command specifies a port identifier.
Parameters 
port-id
The port-id can be configured in one of the following formats:
Values
port-id slot/mda/port[.channel]
bundle-id bundle-type-slot/mda.bundle-num
bundle keyword
type ima|ppp
bundle-num 1 — 256
bpgrp-id bpgrp-type-bpgrp-num
bpgrp keyword
type ima, ppp
bpgrp-num 1 — 256
aps-id aps-group-id[.channel]
aps keyword
group-id 1 — 64
ccag-id ccag-id.<path-id>[cc-type]
ccag keyword
id 1 — 8
path-id a, b
cc-type [.sap-net|.net-sap]
eth-tunnel-id - eth-tunnel-id
eth-tunnel keyword
id 1 — 1024
lag-id lag-id
lag keyword
id 1— 200